Tutorials

  • Design & CAD ×
  • Modeling ×
  • Autodesk Inventor ×

New approach in designing and modelling an Oil pump using Inventor 2016

Ebrahim Abu Has
in Design & CAD
120 13 Intermediate
Step by step tutorial videos, showing the easy way of modelling an Oil pump using Inventor 2016, how to create the parts, assemble them and drive gears, new approach make use of most Inventor specs, design center with some new tips & tricks ...
Autodesk Inventor ticks tips some splines parallel shafts keyways keys shaft design gears spur

How to model a Centrifugal Pump Body (Spiral construction) using Inventor 2014?

Constantin STANCESCU
in Design & CAD
76 18 Intermediate
We have to abide by all the conditions from the technical drawing Note: You can watch my live tutorial for modeling this part here: https://youtu.be/yxEAv2p31zw
Autodesk Inventor centrifugal_pump inventor_2014 ipt multi-body spiral coil

LEGO - 01 Basic Dimensions & Bricks Explained

dk
in Modeling
71 9 Intermediate
I get a lot of questions about how I create LEGO parts. This is Part I - The Basics. Most "standard" parts can be created using only simple math. Standard parts consist of square, circular, and angled blocks - regular geometric blocks. I will refer to BrickLink (www.bricklink.com/), but many others use similar methods: Peeron: http://www.peeron.com/ BrickOwl: http://www.brickowl.com/ Brickipedia: http://lego.wikia.com/wiki/LEGO_Wiki etc.
Autodesk Inventor bricks dimensions lego

Cap screws and machine screws

dea
in Drafting
69 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.
Autodesk Inventor screw cap

How do I scale a model in Inventor?

William
in Design & CAD
51 13 Beginner
:)
Autodesk Inventor

LEGO - 02 Building Bricks with Parameters

dk
in Modeling
39 4 Intermediate
I don't get asked this but it is a very powerful tool and will make your life a lot easier. This also applies to other repetitive parts, not just LEGO bricks, and can be applied with the exact same methods.
Autodesk Inventor parameters lego

Tutorial: How to make energy chain and animate that by parameter

barta
in Design & CAD
38 5 Beginner
Step by step
Autodesk Inventor tipsntricks

[VIDEO] Bending Plate Animation Inventor 2020 Tutorial

Didi Widya Utama
in Assemblies
35 1 Intermediate
This tutorial will show how to create a bending process of a plate in animation, hope this video will give you clear explanation. please leave comment below
Autodesk Inventor studio animation plate bending tutorial 2020 inventor autodesk

How to model a Control lever shaft using Inventor 2014?

Constantin STANCESCU
in Design & CAD
33 8 Intermediate
If you are really interested in modeling with Inventor (2014), try to apply every step with respect to their order and watch how you reach the model. You can watch the live modeling of this part with Inventor 2021 by using this link: https://youtu.be/gOkTy_oJdH0 Enjoy!
Autodesk Inventor

Modelling of Impeller

Mohit
in Design & CAD
29 4 Beginner
Modelling of Impeller
Autodesk Inventor cad model centrifugal parts pump impeller

How to model a curved spring

Jens Nielsen
in Modeling
27 8 Intermediate
Let me show you how to use some surface commands which combine in a 3Dsketch for the solid sweep. No coil command needed. on youtube at: https://youtu.be/wcB5OBTrqfA
Autodesk Inventor coil 3dintersection surface sweep spring

Inventor 2019 Crash Course for Complete Beginner

CAD Pond
in Modeling
26 6 Beginner
Still spending so much time, struggling with learning Inventor on your own? You can stop now! Get a detailed explanation of every single tool. This is the first of a series, and I'll like you to check below to know what to expect in this volume. In this Tutorial, I shall introduce briefly the Inventor 2019 interface, demonstrate how to access the inventor self-help learners path, demonstrate the way to set up the software with your desired Unit style, and then put in my best to handle every single sketch tool in detail.
Autodesk Inventor beginner sketch tutorial 2019 inventor autodesk

How to create a Square to Round (Autodesk Inventor)

David Tate
in Modeling
22 5 Beginner
This tutorial will run you through the process to create a sheet metal square to round from start to finish. Including flat pattern.
Autodesk Inventor lengthy inventor round square metal sheet

Simple Injection Mould Design - Plastic Cups Product

Muhammad Yunus
in Modeling
22 0 Intermediate
This tutorial shows you how to create a simple plastic mold design. Two Plate Mold & Single Cavity.
Autodesk Inventor plastic cups mold design plastic injection molding injection mould design

LEGO - 03 Using Data from LDraw

dk
in Modeling
20 0 Intermediate
Sometimes LEGO bricks don't fall into the regular 0.8/1.6mm rule. This will explain how to get "lumpy" 3D surface data from LDraw DAT files and use them to create your own intelligent parts. *I use the AutoDesk Inventor Pro suite, which includes Inventor Pro and 3D Studio Max. I will discuss using certain file formats, but you need to determine what your software will import/export. *I've been told that IV 2017+ will let you measure the LDraw data directly in Inventor, removing the whole 3DMax conversions steps.
Autodesk Inventor ldraw lego
White Stratasys Logo White GrabCAD Logo
© 2025 Stratasys Inc.
ABOUT US
RESOURCES
Support
SOCIAL
Streamline Pro
Control
Print
Pro
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.