Tutorials

  • Composites ×
  • Simulation & CAE ×
  • Engineering Fundamentals ×

Second round of the Novel Cryogenic Recuperator Design

Marcelo Valderrey
in Theory
17 8 Expert
We took as a reference the set of solutions achieved in the NASA CHALLENGE: Novel Recuperator Design for Cryogenic Fluid Management System, and proceeded to enhance the solutions we had proposed. In the M25 Chair - Synthesis of Mechanisms and Machines, we recognize this task as: Divergent-Convergent Creative Postprocessing.
unr smm cryogenic recuperator nasa

Onshape Robot Tutorial for Absolute Beginners (Step-by-Step Guide)

Engineering Juice
in Process Simulation
1 0 Beginner
https://youtu.be/BQ3qsnO2RfY
onshape tutorial prototwin tutorial prototwin onshape prototwin onshape

Introduction to static analysis CAE

Edwin Rodriguez
in FEM
1 0 Beginner
CAE Fundamentals Tutorial, Introduction to static analysis in spanish.

Simulation Contact

Oleksandr Grinenko
in FEM
0 0 Intermediate
Hello people, In this tutorial - contact simulation in FreeCAD FEM Workbench. Mechanical boundary conditions: Plate fully constrained from both sides. Contact between cylinder & plate: Stiffness=70 GPa/m mu_friction=0.3 sigma_P=50 MPa on cylinder face. Material: Steel C45 plate Aluminium zylinder Link to the video with descriptions here: https://vimeo.com/1103103030
plate contact simulation freecad

Тумба прикроватная Начало сборки Часть 1.

Alex Fabriсator
in Process
0 0 Expert
В виде показан процесс сборки прикроватной тумбы из деталей, изготовленных на самодельном лазерном станке
design homemade diy furniture

How to set up nonsteady simulation

Oleksandr Grinenko
in FEM
0 0 Intermediate
Hello people, In this tutorial - nonsteady thermomechanical FEM simulation. Heat flux load for heat sink. Link to the video with descriptions here: https://vimeo.com/1106773772
tutorial heatsink nonsteady thermodynamics simulation freecad

Weld Spacing: Minimum Distance Between Welds According to Standards (ASME & API)

Aygün Karaköse
in Standards
0 0 Expert
In welding design, the minimum distance between welds is a crucial parameter affecting the integrity, inspectability, and performance of welded structures. Improper spacing can lead to: Overlapping Heat Affected Zones (HAZ), Increased residual stress, Cracking or failure under pressure or cyclic loading. This tutorial will guide you through standard-based minimum weld spacing requirements and provide general rules applicable in piping, pressure vessels, and tank structures.
engineer welding weld

Simulasi Fluida di Air Shaper

khoirul anam
in CFD
0 0 Beginner
Senang sekali bisa berbagi kemajuan terbaru dalam proyek saya! Saya baru saja menyelesaikan desain 3D untuk Roda Pemanen Kelapa Sawit yang Inovatif, lengkap dengan sistem suspensi terintegrasi, menggunakan Autodesk Fusion 360. Proses desain ini merupakan tantangan menarik dalam mengoptimalkan performa dan daya tahan roda, terutama di medan perkebunan kelapa sawit. Setelah desain 3D rampung, saya melangkah lebih jauh dengan melakukan simulasi aerodinamis dan fluid dynamics menggunakan Airshaper. Langkah ini krusial untuk menganalisis dan memvalidasi efisiensi desain, mengidentifikasi potensi area optimasi, dan memastikan kinerja optimal di lapangan. Pengalaman ini tidak hanya memperdalam pemahaman saya tentang desain komponen berat dan sistem suspensi, tetapi juga mempertajam kemampuan saya dalam memanfaatkan simulasi canggih untuk validasi rekayasa. Senang bisa terus belajar dan berinovasi! #DesainProduk #RekayasaMekanis #Fusion360 #Airshaper #Simulasi #Inovasi #KelapaSawit
desainproduk rekayasamekanis fusion360 airshaper simula

Understanding Root Opening (Gap Distance) in Butt Welds – A Standards-Based Tutorial (ASME & ISO)

Aygün Karaköse
in Standards
0 0 Expert
In welding, especially butt welds, the "gap" or root opening is a critical factor that directly affects weld penetration, quality, and strength. This tutorial explains what root opening is, why it matters, how it varies by material thickness and process, and what international standards like ASME Section IX and ISO 9692-1 say about it.
weld engineer welding
White Stratasys Logo White GrabCAD Logo
© 2025 Stratasys Inc.
ABOUT US
RESOURCES
Support
SOCIAL
Streamline Pro
Control
Print
Pro
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.