Tutorials

  • Drafting ×
  • Process Simulation ×
  • Process ×
  • Other ×

How to Raise Your GrabCAD Score

FredSWUG
in Process
82 31 Beginner
Your score on GrabCAD is not terribly important, but it is nice to have a better score, and not be "ranked" dead last on a site with four million users. What can you do to increase your score?
points ranking score grabcad

Cap screws and machine screws

dea
in Drafting
67 12 Intermediate
Cap screws and machine screws are similar in shape, differing only in their relative sizes. Machine screws are usually smaller in size, compared to cap screws. These are used for fastening two parts, one with clearance hole and the other with tapped hole. The clearance of the unthreaded hole need not be shown on the drawing as its presence is obvious. Figure 5.24 shows different types of cap and machine screws, with proportions marked Cap screws are produced in finish form and are used on machines where accuracy and appearance are important. As cap screws are inferior to studs, they are used only on machines requiring few adjustments and are not suitable where frequent removal is necessary. These are produced in different diameters, upto a maximum of 100 mm and lengths 250 mm. Machine screws are produced with a naturally bright finish and are not heat treated. They are particularly adopted for screwing into thin materials and the smaller ones are threaded throughout the length. They are used in fire-arms, jigs, fixture and dies. They are produced in different diameters upto a maximum of 20 mm and lengths upto 50 mm.
Autodesk Inventor screw cap

Ejercicio SMM - Parte 5

Marcelo Valderrey
in Other
58 0 Beginner
Recursos visuales orientados a la creación de presentaciones a partir de imágenes, animaciones y videos.
unr smm

Ejercicio SMM - Parte 1

Marcelo Valderrey
in Other
58 0 Beginner
Bajar un modelo de parte en formato STEP, importarlo, repararlo y guardarlo como parte de SolidWorks.
SOLIDWORKS unr smm

Ejercicio SMM - Parte 4

Marcelo Valderrey
in Other
57 0 Beginner
Exportar un ensamblaje en formato STEP. Abrir ensamblajes en modo LARGE DESIGN REVIEW. Convertir ensamblajes con MAKE VIRTUAL.
unr smm

Ejercicio SMM - Parte 3

Marcelo Valderrey
in Other
56 0 Beginner
Crear un ensamblaje a partir de distintas configuraciones de una misma pieza.
unr smm

Ejercicio SMM - Parte 8

Marcelo Valderrey
in Other
56 0 Beginner
SolidWORKS Motion - Animación
unr smm

Ejercicio SMM - Parte 7

Marcelo Valderrey
in Other
55 0 Beginner
Vistas en sección, en explosión y algunas animaciones automáticas.
unr smm

Ejercicio SMM - Parte 2

Marcelo Valderrey
in Other
55 0 Beginner
Generar configuraciones dentro del archivo de parte eliminando selectivamente sus sólidos.
unr smm

Ejercicio SMM - Parte 6

Marcelo Valderrey
in Other
55 0 Beginner
Continuando con los recursos visuales orientados a la creación de presentaciones, veremos elementos básicos para crear imágenes renderizadas.
unr smm

Ejercicio SMM - Parte 9

Marcelo Valderrey
in Other
54 0 Beginner
SolidWORKS Motion - Movimiento básico
unr smm

SOLIDWORKS Visualize 2019 Tutorial - How to Render A Spider Robot Motion Study as Realistic.

Ahmed ElPrince
in Other
50 1 Expert
This Video Below Will Help You as a Beginner to know the Basics of Rendering Any Motion Study from SOLIDWORKS Software, Also Some Tricks inside Visualize will be explained after watching This VIDEO. If You Understand and Learnt Something New ... Please Like And Subscribe My New Channel (Prince EnGineer).. if You have any Question I'll Reply and Thanks For Watching Link: https://www.youtube.com/watch?v=PNJmwm6g1cA&t=123s
3d animation video visualize solidworks render robot spider

I Built a Military Robot

Engineering Juice
in Process
45 6 Intermediate
Mobile, military robot optimized for use in desert environments which can be controlled remotely or autonomously and can collect/ stream video to a VR headset via its front mounted camera. The method of movement is a continuous track, created using steel roller chain connected by fasteners with 3D printed links. These loops sit on a custom designed drive sprocket and idler sprocket with 4 shock absorber loaded roller pins that act as the suspension system. The drive motors are powered by '18650' batteries, directed by a raspberry pi 4 and connected to a motor controller. For connectivity, a mobile device can connect to the pi's external antenna as it is a WiFi access point. From here, directions can be sent to the robot from the mobile device using the Node Red GUI and additionally, the entirety of the main raspberry pi computer can be accessed for the use of sending custom commands for autonomous movement.
Fusion 360 printed 3d rc programming pi raspberry electronics 360 fusion robot robotics

How to save your animations as GIFs in SolidWorks

Yahya T Khedr
in Other
33 3 Intermediate
Do you want to know how to make GIFs of your animations? Ever asked yourself how they did it? Here I'll show you how to make seamless GIFs from your animations using SolidWorks, as well as PhotoScape... I chose PhotoScape as it has decent results, doesn't cause any bumping & - most important - is for free. You can download the latest version from here: http://www.photoscape.org/ps/main/download.php
animation render software photoscape rendering photoview gif solidworks

How to Prepare Your 3D Model for Manufacture

Russell Everard
in Process
32 1 Expert
Using this ladies bike model found in the thousands of models available on GrabCAD I have made a step-by-step guide on how to break down your top level assembly for the workshop or for outsourcing.
SOLIDWORKS cutting laser fabrication cnc fixings assemblies manufacture solidworks
White Stratasys Logo White GrabCAD Logo
© 2025 Stratasys Inc.
ABOUT US
RESOURCES
Support
SOCIAL
Streamline Pro
Control
Print
Pro
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.